CAN Gateway Pinout » History » Version 16
Adam Klama, 01/09/2025 11:13 AM
| 1 | 1 | Adam Klama | # CAN Gateway Pinout |
|---|---|---|---|
| 2 | 2 | Adam Klama | |
| 3 | 15 | Adam Klama | Connector: 1473712-1 (TE Connectivity Superseal 1.0mm 26pos, 2 row version) |
| 4 | Terminals: |
||
| 5 | 16 | Adam Klama | * 1-1437284-0 (16AWG-14AWG / 1.25-2mm^2) |
| 6 | * 1437284-9 (18AWG-16AWG / 0.75-1.25mm^2) |
||
| 7 | 15 | Adam Klama | * 1437284-9 (20AWG-14AWG) |
| 8 | |||
| 9 | 11 | Adam Klama | |Pin Name | Pin | Pin | Pin Name | |
| 10 | |-----------------|-----|-----|------------| |
||
| 11 | | KL30 IN | 1 | 14 | KL31 | |
||
| 12 | | KL30B OUT | 2 | 15 | KL15IN | |
||
| 13 | | PWR6/WAKEUP OUT | 3 | 16 | AN1/PWR1 | |
||
| 14 | | AN2/PWR2 | 4 | 17 | AN3/PWR3 | |
||
| 15 | 14 | Adam Klama | | AN4/PWR4 | 5 | 18 | AN5/PWR5 | |
| 16 | 11 | Adam Klama | | AN6 | 6 | 19 | AN7 | |
| 17 | | AN8/FREQ2 | 7 | 20 | AN9/FREQ1 | |
||
| 18 | | AN10/FREQ4 | 8 | 21 | AN11/FREQ3 | |
||
| 19 | | SENSOR5V | 9 | 22 | sGND | |
||
| 20 | | CAN1H | 10 | 23 | CAN1L | |
||
| 21 | | CAN2H | 11 | 24 | CAN2L | |
||
| 22 | | CAN3H | 12 | 25 | CAN3L | |
||
| 23 | | CAN4H | 13 | 26 | CAN4L | |
||
| 24 | 3 | Adam Klama | |
| 25 | |||
| 26 | # Pin description |
||
| 27 | |||
| 28 | 7 | Adam Klama | Terminal names starting with KL are names according to [DIN 72552](https://en.wikipedia.org/wiki/DIN_72552) |
| 29 | 3 | Adam Klama | |
| 30 | ## KL31 |
||
| 31 | 6 | Adam Klama | KL31 - return to battery- or chassis ground. This pin should be connected with wire of at least 1.5mm<sup>2</sup> |
| 32 | 3 | Adam Klama | |
| 33 | ## KL30 IN |
||
| 34 | KL30 - constant battery+ This device is optimized for low power consumption in standby - 0.5mA - it is strongly recommended to keep this terminal on constant bat+ or delayed off. |
||
| 35 | 6 | Adam Klama | This pin should be wired wit at least 1.5mm<sup>2</sup> |
| 36 | 3 | Adam Klama | |
| 37 | ## KL30B OUT |
||
| 38 | KL30B - delayed off battery+. This pin is intended to power the transmission and is capable of supplying 15A. |
||
| 39 | |||
| 40 | ## KL15IN |
||
| 41 | 6 | Adam Klama | KL15 - Battery + through ignition switch. This pin should be connected with wire of 0.35mm<sup>2</sup> |
| 42 | 3 | Adam Klama | |
| 43 | 14 | Adam Klama | ## ANx - x between 1 and 7 |
| 44 | 3 | Adam Klama | ANx - Analog input capable of measuring voltages of up to 16V |
| 45 | |||
| 46 | 14 | Adam Klama | ## ANx - x between 8 and 11 |
| 47 | 12 | Adam Klama | ANx - Analog input capable of measuring voltages of up to 6V |
| 48 | 3 | Adam Klama | |
| 49 | 13 | Adam Klama | ## PWRy - y between 1 and 6 |
| 50 | 3 | Adam Klama | PWR1 - Low current power output capable with current rating of 0.9A |
| 51 | |||
| 52 | ## FREQz - z between 1 and 4 |
||
| 53 | FREQz - Inputs for speed signals |
||
| 54 | 4 | Adam Klama | |
| 55 | ## sGND |
||
| 56 | sGND - this pin supplies ground, for all sensors connected to analog and frequency inputs. |
||
| 57 | |||
| 58 | ## SENSOR5V |
||
| 59 | SENSOR5V - this pin supplies 5V to sensors connected to analog and frequency inputs. |
||
| 60 | |||
| 61 | ## CANxL and CANxH - x between 1 and 4 |
||
| 62 | This pin pairs are used to connect gateway to different CANbus networks. |
||
| 63 | Inside device there are 0805 pads for 120R resistor for termination. |