CAN Gateway Pinout » History » Version 12
Adam Klama, 08/01/2024 08:08 PM
| 1 | 1 | Adam Klama | # CAN Gateway Pinout |
|---|---|---|---|
| 2 | 2 | Adam Klama | |
| 3 | 11 | Adam Klama | |Pin Name | Pin | Pin | Pin Name | |
| 4 | |-----------------|-----|-----|------------| |
||
| 5 | | KL30 IN | 1 | 14 | KL31 | |
||
| 6 | | KL30B OUT | 2 | 15 | KL15IN | |
||
| 7 | | PWR6/WAKEUP OUT | 3 | 16 | AN1/PWR1 | |
||
| 8 | | AN2/PWR2 | 4 | 17 | AN3/PWR3 | |
||
| 9 | | AN4/PWR5 | 5 | 18 | AN5/PWR5 | |
||
| 10 | | AN6 | 6 | 19 | AN7 | |
||
| 11 | | AN8/FREQ2 | 7 | 20 | AN9/FREQ1 | |
||
| 12 | | AN10/FREQ4 | 8 | 21 | AN11/FREQ3 | |
||
| 13 | | SENSOR5V | 9 | 22 | sGND | |
||
| 14 | | CAN1H | 10 | 23 | CAN1L | |
||
| 15 | | CAN2H | 11 | 24 | CAN2L | |
||
| 16 | | CAN3H | 12 | 25 | CAN3L | |
||
| 17 | | CAN4H | 13 | 26 | CAN4L | |
||
| 18 | 3 | Adam Klama | |
| 19 | |||
| 20 | # Pin description |
||
| 21 | |||
| 22 | 7 | Adam Klama | Terminal names starting with KL are names according to [DIN 72552](https://en.wikipedia.org/wiki/DIN_72552) |
| 23 | 3 | Adam Klama | |
| 24 | ## KL31 |
||
| 25 | 6 | Adam Klama | KL31 - return to battery- or chassis ground. This pin should be connected with wire of at least 1.5mm<sup>2</sup> |
| 26 | 3 | Adam Klama | |
| 27 | ## KL30 IN |
||
| 28 | KL30 - constant battery+ This device is optimized for low power consumption in standby - 0.5mA - it is strongly recommended to keep this terminal on constant bat+ or delayed off. |
||
| 29 | 6 | Adam Klama | This pin should be wired wit at least 1.5mm<sup>2</sup> |
| 30 | 3 | Adam Klama | |
| 31 | ## KL30B OUT |
||
| 32 | KL30B - delayed off battery+. This pin is intended to power the transmission and is capable of supplying 15A. |
||
| 33 | |||
| 34 | ## KL15IN |
||
| 35 | 6 | Adam Klama | KL15 - Battery + through ignition switch. This pin should be connected with wire of 0.35mm<sup>2</sup> |
| 36 | 3 | Adam Klama | |
| 37 | ## ANx - x between 1 and 8 |
||
| 38 | ANx - Analog input capable of measuring voltages of up to 16V |
||
| 39 | |||
| 40 | ## ANx - x between 9 and 12 |
||
| 41 | 12 | Adam Klama | ANx - Analog input capable of measuring voltages of up to 6V |
| 42 | 3 | Adam Klama | |
| 43 | ## PWRy - y between 1 and 5 |
||
| 44 | PWR1 - Low current power output capable with current rating of 0.9A |
||
| 45 | |||
| 46 | ## FREQz - z between 1 and 4 |
||
| 47 | FREQz - Inputs for speed signals |
||
| 48 | 4 | Adam Klama | |
| 49 | ## sGND |
||
| 50 | sGND - this pin supplies ground, for all sensors connected to analog and frequency inputs. |
||
| 51 | |||
| 52 | ## SENSOR5V |
||
| 53 | SENSOR5V - this pin supplies 5V to sensors connected to analog and frequency inputs. |
||
| 54 | |||
| 55 | ## CANxL and CANxH - x between 1 and 4 |
||
| 56 | This pin pairs are used to connect gateway to different CANbus networks. |
||
| 57 | Inside device there are 0805 pads for 120R resistor for termination. |